Jiangsu Kelon Dc Motor Manufacturing Co., Ltd

ZBL4 series fully closed DC motor

一．Characteristics and uses

ZBL4 series fully closed direct cooling type DC motor, is my factory in Z4 series of forced air-cooled motor on the development of new products. Besides its original ZBL4 series motor characteristic of small volume, light weight, large output power, fully applicable to static integration of electric current and other characteristics, but also has a closed casing, therefore particularly suitable for dust and metal scraps and other places.

This series motor adopts the lamination machine, so the application conditions for static rectifier power supply, and can withstand current changes the whole machine cannot achieve rate, the stator adopts an octagonal structure, space utilization high, pole installation location is exact, and using computer aided design, so that the electrical parameter control properly, thus reversing the motor's performance well, the outer surface of the base with a radiating rib special, increases the effective surface area for heat dissipation motor. In order to improve the output power of the motor under the effective volume.

F insulating materials used motor. Insulation structure of novel and reliable, to ensure stable performance and good heat insulation.

Rated voltage of the motor 400 volts or 440 Volts, in three-phase full-controlled bridge rectifier power supply and no external conditions of DC smoothing reactor, long-term stable operation. Rated voltage of 160 volt motor consists of a single-phase power supply rectifier bridge, at this time is the ripple current, the motor circuit must access the DC smoothing reactor, the inductance value see technical data sheet.

Installation dimension of the series motor in addition to the two foot hole axial size " B", are in line with international standards IEC72

二 Demonstration of the type

For example:

The end cap code：端盖代号： Armature core length code：电枢铁心长度代号：

Motor center height ( mm )；电机中心高（毫米）：

The fourth series design：第四次系列设计

The whole closed type ：全封闭自冷式DC machine：直流电机

Motor core length code：电机铁心长度代号

number of poles：极数

三．Motor performance

1.technical data table data should work according to the following conditions

a. Not more than 1000 metres above sea level

b. Ambient air temperature is not more than 40 degrees Celsius

c.The working environment should not contain acid, alkali and other corrosive effect on the insulation gas

d. motor for continuous working system ( S1 )

e:The armature circuit and the excitation circuit of E. motor by static rectifier power supply, also adapted by DC power supply

f:This series motor performance conforms to the national standard GB755-87 " rotary motor basic technical requirements " also with reference to the International Electrotechnical Commission Standard IEC34-1 or the German national standard DIN57530 requirements. 2 to derive 220V, 400V or other voltage .

3 Motor speed is 3000,1500,750 rpm, a total of 4 stalls. To reduce the excitation voltage is constant power speed, speed range, see technical data sheet, reduce the armature voltage is constant torque speed. In the armature current continuous conditions, the minimum speed of 20 rpm, at this time still can maintain the rated torque, speed smooth..

4 Standard excitation voltage of 180 volts, other excitation voltage can be negotiated .In order to ensure that the insulating reliability of excitation system, the excitation circuit is disconnected, shall be connected in parallel at two ends of the excitation winding a release of resistance, to prevent the self-induction, in standard excitation voltage when its value is about seven times the excitation winding resistance ( cold ), excitation voltage higher than the standard value, shunt release resistance value can be less than seven times, and seven times greater than.

5 The outlet box the motor provides a ground sign posts.

6 technical data sheet of the efficiency value of the rated power, rated voltage and speed efficiency, it includes excitation loss

四 Brief introduction of structure

1. Protection grade of the motor is IP44

2. Cooling motor for IC0041 full closed type

3. Install motor in accordance with international GB997-81, IMB3, IMB5, IMB35, IMV1, IMV15, IMV3， IMV36

4．The motor casing surface with radiating ribs, the outlet box cover above the commutator side

5 Non rotating motor side can be equipped with tachogenerator, encoders and other accessories

五．Order goods note

1. Before ordering, please refer to the product catalog, specifications and other data clearly required products, such as the different specifications and directory, or have special requirements, please put forward specific requirements, in consultation with the relevant departments of our factory, with the consent of the signing of the contract or the tentative agreement.

2. When ordering, please indicate the type of motor, power, voltage, speed, working system, structure types, excitation system, the excitation voltage, the number of axles, the outlet box position, as well as required with accessories, spare parts name

3. As the use of special circumstances, need to wet tropical type, prototype number please indicate " TH "

Mode	Rated Power	Rated Speed	Weak Magetism Speed	Armature Current	Excition Power	Efficience	Moment of inertia	Weight
	Pn	nN	nf	In	Pr	m	GD2	Wt
	kw	r/min	r/min	A	W	%	kg.m2	Kg
ZBL4- 100-1	1.1	3000	3600	8.4	120	74.9	0.044	60
	0.75	1500	3000	5.7		71.6
	0.55	1000	2000	4.4		67.7
ZBL4- 100-2	1.5	3000	3600	11.2	120	79.7	0.056	70
	1.1	1500	3000	8.1		77.6
	0.75	1000	2000	5.8		71.9
	0.55	750	1500	4.4		67
	1.5	2680	3600	4.5		81.1
	1.5	3000	3000	4		81.3
ZBL4- 100-3	2.2	3000	3600	15.8	120	84.2	0.076	85
	1.5	1500	3000	10.9		80.1
	0.75	750	1500	5.8		71.9
	2	2700	3600	5.8		85
	2.2	3000	3600	5.7		85.4
	1.3	1370	3000	3.9		81.3
	1.5	1500	3000	3.9		82.2
ZBL4- 112/2-3	3	3000	3600	21.8	140	83.5	0.108	95
	1.1	1000	2000	8.1		74.5
	2.7	2700	3600	7.8		83.7
	2	2700	3600	7.9		84.3
ZBL4- 112/2-4	2.2	1500	3000	15.9	140	81.6	0.144	115
	1.5	1000	2000	11		78.2
	1.1	750	1500	8.3		73.4
	2	1360	3000	5.8		82.5
	2.2	1500	3000	5.7		83.3
	1.3	910	2000	3.9		78.1
	1.5	1000	2000	4		79.6
ZBL4- 132-2	4	3000	3600	29.1	170	83.3	0.4	140
	3	1500	3000	21.7		83
	2.2	1000	2000	16.4		79
	1.5	750	1500	11		74
	4	2750	3600	11.6		84.2
	4	3000	3600	10.4		84.4
	3	1390	3000	8.7		85
	3	1500	3000	7.7		85
	2.2	935	2000	6.5		82
	2.2	1000	2000	5.8		82
	1.5	685	1500	4.5		77.1
	1.5	750	1500	4		77.7
ZBL4- 132-3	5.5	3000	3600	39.7	190	85.3	0.48	165
	4	1500	3000	28.1		84.7
	3	1000	2000	21.5		82.4
	2.2	750	1500	16		80.2
	5	2670	3600	14.2		87.2
	5.5	3000	3600	14.1		87.4
	3.7	1320	3000	10.5		86.1
	4	1500	3000	10.2		86.4
	2.8	880	2000	8.2		83.2
	3	1000	2000	7.8		83.5
	2	680	1500	5.9		80.6
	2.2	750	1500	5.9		81.8
ZBL4- 160-31	5.5	1500	3000	38.7	230	85.5	0.88	250
	4	1000	2000	38.2		84.6
	3	750	1500	21.3		81.6
	7.5	2700	3600	21		87.7
	7.5	3000	3600	19.2		88
	5.5	1360	3000	15.4		87
	5.5	1500	3000	13.9		87.4
	4	900	2000	11.4		84.5
	4	1000	2000	10.3		85.1
	3	680	1500	8.6		82.2
	3	750	1500	7.7		82.9
ZBL4- 180-21	5.5	1000	2000	38.7	230	84.7	1.72	330
	4	750	1500	28.9		82.3
	11	2700	3600	30.5		88.7
	11	3000	3600	27.8		89
	7	1360	3000	19.6		87.7
	7.5	1500	3000	18.9		88
	5	900	2000	14.2		85.3
	5.5	1000	2000	14		86.1
	4	680	1500	11.6		83.1
	4	750	1500	10.3		83.9
ZBL4- 180-31	13.6	2700	3600	37.4	250	90.3	1.92	360
ZBL4- 180-31	15	3000	3600	37.4	250	90.5	1.92	360
ZBL4- 180-41	5.5	750	1500	38.6	260	84.8	2.2	390
	9.5	1360	3000	26.1		88.8
	11	1500	3000	27.4		89
	7	895	2000	19.4		87.5
	7.5	1000	2000	18.8		88.1
	5	675	1500	14		85.6
	5.5	750	1500	13.8		86.3
ZBL4- 180-51	6.8	680	1500	18.9	270	86.5	2.52	430
ZBL4- 180-51	7.5	750	1500	18.7	270	87.3	2.52	430